不錯蓄電池總代理

時間：2018-06-19作者：北京金業順達科技有限公司瀏覽：82

不錯蓄電池總代理





成功檢測不錯蓄電池狀態的前提是可以提供需要的交流恒流源。恒流源是能夠向負載提供恒定電流的電源裝置。它是一個電源內阻非常大的電源。為了保證內阻有較高的測量精度及較好的重現性，要求恒流電流源有足夠的穩定度，并且波形失真度要小。這里所需交流信號幅度為40mV，頻率為1KHZ

The premise of successful detection of battery state is that it can provide the needed AC constant current source. The constant current source is a power supply that can provide a constant current to the load. It is a power supply with a very large internal resistance. To ensure that the internal resistance has high measurement accuracy and good reproducibility, constant current source is required to have enough stability and waveform distortion is small. The magnitude of the AC ** required here is 40mV and the frequency is 1KHZ.
但是傳統的低頻交流信號發生器設計中存在很多的不足：應用通用電路,元器件多,尤其是電容的體積大,且波形的穩定性差、失真大,調節也較不方便；應用**電路,如ICL8038、MAX038等,其失真和穩定性方面有明顯提高,但低頻應用時不合適,調節不方便,成本也較高。
But there are many shortcomings in the traditional low frequency AC ** generator design: the application of general circuit, many components, especially the volume of the capacitance, and the poor stability and distortion of the waveform, and very inconvenient to adjust. The application of special circuit, such as ICL8038, MAX038 and so on, has obviously improved the distortion and stability, but it is used in low frequency. It is not suitable, the adjustment is inconvenient, the cost is also high.




3．1 設計原理
3.1 design principle




本文采用了數字式信號發生器產生標準正弦波和電流負反饋法產生精確交流恒流源法, 交流恒流源實現原理如圖2所示。
In this paper, a digital ** generator is used to produce a standard sine wave and a current negative feedback method to produce an accurate AC constant current source method, and the principle of AC constant current source realization is shown in Figure 2.












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








電路組成框圖如圖2所示：這是一個閉環控制系統，電流負反饋電路。標準正弦波產生一個頻率穩定、對稱、失真度低的1KHz正弦波信號。驅動電路把正弦波放大，去推動功放電路，得到正弦交流電流輸出。恒流控制電路從功放輸出中得到的信號，通過與給定的信號相比較，來調節驅動電路的信號，從而使輸出電流保持穩定。
The block diagram of the circuit is shown in Figure 2: This is a closed loop control system and a current negative feedback circuit. The standard sine wave produces a 1KHz sine wave with stable frequency, symmetry and low distortion. The driving circuit amplifies the sine wave to drive the power amplifier circuit, and obtains the sinusoidal AC current output. The ** obtained from the output of the power amplifier by the constant current control circuit, by comparing with the given **, adjusts the ** of the driving circuit, so that the output current is kept stable.




3．2 標準正弦波的產生原理
The principle of the generation of 3.2 standard sine wave




標準正弦波信號的產生采用數字式信號發生器。首先將正弦表數據存儲在如圖3所示的正弦信號存儲器中,晶振產生振蕩頻率f，經過整型電路變?yōu)橥暾讲l率，再經過R分頻電路得到頻率為f/R,再經過鑒相器FD和環路濾波器LF電路鎖相分頻后，讀取存儲在正弦信號存儲器中的正弦值,經過D/A轉換電路和經低通有源濾器濾波電路，生成圖2 所需的標準正弦波。
The standard sine wave ** is generated by digital ** generator. First, the sinusoidal data is stored in the sinusoidal ** memory as shown in Figure 3. The oscillator produces an oscillating frequency f, after the integral circuit is transformed into a complete square wave frequency, and then the frequency is f/R through the R frequency division circuit, and then after the phase discriminator FD and the loop filter LF circuit are locked in phase, the reading stored in the sinusoidal ** memory is read. String value, through D/A conversion circuit and low-pass active filter filter circuit, generate standard sine wave required for Figure 2.


由于電池內阻為毫歐級，因此采用常規的兩端子測量方法測量誤差較大，在此采用四端子測量方式。測量時兩個端子施加一頻率為
Because the internal resistance of the battery is millieu level, the conventional two terminal measurement method has great error, and the four terminal measurement method is adopted. At the time of measurement, two terminals are applied in a frequency








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




的恒定交流激勵電流信號，另兩個端子用于測量。測量工作原理圖如圖1所示，響應信號是指蓄電池注入交流恒流源后，在其兩端測出的交流電壓信號。而正弦信號是經D/A產生的作為壓控恒流源的輸入信號。
A constant AC excitation current ** and the other two terminals are used for measurement. The working principle diagram is shown in Figure 1. The response ** is the AC voltage ** measured at both ends after the battery is injected into the AC constant current source. Sinusoidal ** is generated by D/A as the input ** of voltage controlled constant current source.
























設正弦信號為：
The sine ** is set as:








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery












（1）
(1)
蓄電池兩端的響應電壓信號為：
The response voltage **s at both ends of the battery are:








（2）
(2)








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery
為注入蓄電池的交流電流和其兩端響應電壓信號的相位差。
The phase difference between the AC current and the voltage **s at both ends of the battery is injected.
通過模擬乘法器后有：
After the analog multiplier, there are:








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




K為模擬乘法器的放大系數。
K is the magnification factor of the analog multiplier.
進行低通濾波后濾掉交流成分得：
After low pass filtering, filter off the AC component:












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（3）
(3)




由交流法測內阻原理得：
The principle of measuring internal resistance by AC method is obtained.








精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery




（5）
(5)
式中I為交流恒流源信號的較大值。比較（4）、（5）可得：
I is the maximum value of the AC constant current source **. Comparison (4) and (5) can be obtained:












精確測量蓄電池內阻方法的研究
Study on the method of accurately measuring the internal resistance of the battery








上式中K、A、I都是已知量，而u為經過A/D采樣送到單片機進行處理的采樣值，所以在單片機中進行一個簡單的除法運算便能得到蓄電池內阻了。
The K, A and I in the upper form are all known, while u is sampled by the A/D sample to the single chip processor, so a simple division operation in the single chip can get the internal resistance of the battery.

北京金業順達科技有限公司專注于APCUPS電源,圣陽蓄電池,科士達UPS電源,UPS蓄電池,山特UPS電源,艾默生ups電源,松下蓄電池,理士蓄電池,湯淺蓄電池,艾默生精密空調,精密空調廠家,山特UPS電源廠家,直流屏蓄電池,模塊化機房,一體化機房等, 歡迎致電 18201588123

• 詞條

  詞條說明

• 東洋蓄電池6GFM38

  東洋蓄電池6GFM38 東洋蓄電池不短路的原因 這種情況往往發生在電池焊線維護和運輸過程中。東洋蓄電池短路會直接導致電池打火或者起*炸。當發現使用過一段時間后電池出現斷線的情況需要重新焊線時，特別要注意電烙鐵不要同時接觸電池的正極和負極。另外在去飛場運輸電池的過程中，較好的辦法是，沒個電池都單獨套上自封袋，防止因運輸過程中，因顛簸和碰撞導致某片電池的正極和負極同時碰到其他導電物質而短路。 電調

• 東洋蓄電池12V65AH

  東洋蓄電池12V65AH 2、不要使任何外來的雜質落進蓄電池內。 3、端子的接觸必須可靠，必要時可涂上凡士林，對端子不可擰力過大，保證端子的清潔，防止端子腐蝕。 4、檢查排氣栓或密封蓋上的排氣孔，必須使之隨時保持通暢，防止堵塞造成爆炸。 5、開口蓄電池留意液面高度，定期補加（純凈水或者蒸餾水），不要讓較板和隔板露出液面。 6、必須將電解液調整到正常高度，而且只能在蓄電池充電終止時進行。 7、電解

• 湯淺蓄電池2V1660AH

  湯淺蓄電池2V1660AH 湯淺蓄電池內阻的測量方法 ? ?假如湯淺蓄電池內阻失效或容量缺少.就有或許構成重大事故，所以有必要對蓄電 池的工作參數進行悉數的在線監測。湯淺蓄電池作為電源體系停電時的備用電源。己廣泛的運用于工業生產、交通、通訊等工作。蓄電池情況的首要標志之一即是它的內阻。 ? ?無論是蓄電池即將失效、容量缺少或是蓄電池充放電不妥，都能從它的內

• OTP蓄電池6FM-17

  OTP蓄電池使用注意事項： 1、6FM12V/3FM6V/GFM2V系列鉛酸蓄電池可以象常規電池一樣直立安裝使用，也可臥式使用。 2、蓄電池應離開熱源和易產生火花的地方，并避免陽光直射及置于大量**溶劑氣體和具有腐蝕性氣體的環境中。其安全距離應大于0.5m。 3、蓄電池室應具有必要的通風、照明設施，避免安裝在密閉設備或容器中。電池間距好在15mm以上。 4、蓄電池均荷電出廠，在運輸、安裝過程中謹防