Configuring additional drives on PROFINET (X150) as isochronous

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：124

Configuring additional drives on PROFINET (X150) as isochronous



Requirement

STEP 7, V16 or higher

SINAMICS Startdrive, V16 or higher

You can import drives that are not integrated in the TIA Portal via Startdrive using GSD files (generic station description). To do so, install the drive in the "Options" menu as a device description file (GSD).

Adding a drive and frame to the device configuration

Add the required drive system in the network view, for example, SINAMICS S120 CU320-2 PN.

Open the device view of the drive system and configure the drive objects.
You can find the relevant details in the SINAMICS S120 with Startdrive commissioning manual.

Open the network view. Assign the drive system to the PROFINET interface [X150] of the CPU.

Open the topology view. Interconnect the port of the drive system as in the real configuration with the port of the CPU.

Configure the PROFIdrive frames for the drive axes, for example, frame 105.

提示 If you use a PROFINET IO drive system other than SINAMICS S120, adding and configuring may differ from the description in certain respects. The frame is automatically preassigned in line with the drive system.




Activating isochronous mode in the device configuration

You can operate PROFINET drives in isochronous or non-isochronous mode. Isochronous mode, however, increases the quality of the position control of the drive and is therefore recommended for drives such as SINAMICS S120.

Proceed as follows to activate isochronous mode for the drive:

Select the device view of the drive system.

In the properties window, select the tab "PROFINET Interface [X150]" > "Advanced options" > "Isochronous mode".

Select the "Isochronous mode" check box.

In the properties window, select the tab "PROFINET Interface [150]" > "Advanced options" > "Real-time settings" > "Synchronization".

Select "IRT" as the RT class.

提示 If you have configured a PROFIdrive frame at the drive that requires isochronous mode, STEP 7 automatically sets "Isochronous mode" and the RT class "IRT".




Configuring the PLC as sync master and setting the send clock

Select the device view of the CPU.

In the properties window, select the tab "PROFINET interface [X150]" > "Advanced options" > "Real-time settings" > "Synchronization".

Select "IRT" as the RT class if it has not already been set automatically.

Select "Sync master" from the "Synchronization role" drop-down list.

Click the "Domain settings" button.

Set the required send clock.

Selecting the drive in the configuration of the technology object

Add a new axis technology object.

Open the configuration "Hardware interface" > "Drive".

Select the "PROFIdrive" entry from the "Drive type" drop-down list.

Select a drive axis of the PROFINET drive unit from the "Drive" list.
Only drives for which you have configured a suitable PROFIdrive frame are available for selection. You can find out which PROFIdrive frames are supported by the SIMATIC Drive Controller in the S7?1500T Motion Control function manuals.

Using the "Device configuration" button, you can switch to the drive device view, for example, to configure drives or set other PROFIdrive frames (for example 39x frame for the X122/X132 IOs of a CU320?2).

Setting the clock system

You have configured an external drive as isochronous on PROFINET using the example of the SINAMICS S120 CU320?2 PN. Next, set the clock system.

Choose between independent and coupled isochronous mode.

Set the required send clock.

Assign the "MC Servo" OB the clock system of the PROFINET interface X150.


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• MAC ACL入站規則

  入站規則簡介在此頁面上* ACL 規則，接口將根據此規則過濾入站幀。在“規則組態”(Rules Configuration) 選項卡中* ACL 規則。顯示框說明該頁面包含以下框：接口從下拉列表中選擇所需接口。根據具體設備顯示可用接口。添加規則 (Add Rule)選擇要分配給接口的 ACL 規則。在“規則組態”(Rules Configuration) 頁面中* ACL 規則。添加 (Ad

• Web 頁面尺寸的相關建議

  Web 頁面尺寸的相關建議Web 頁面大小對所需內存和性能的影響內容豐富的 HTML 頁面，尤其是包含許多圖片的頁面，將占用大量的裝載存儲器空間。請注意以下事項：選擇的 SIMATIC 存儲卡的容量應足以提供充足的裝載存儲器空間。將 HTML 頁面的數據量限制為 1 MB。如果 HTML 頁面的數據量**出 1?MB，則會導致性能下降，因為緩存中只能保存 1?MB 的數據。將 H

• 組態系統功能 手動設置時間

  手動設置時間手動設置系統時間在此頁面上設置系統的日期和時間。要使用該設置，請啟用“手動設置時間”(Manual time setting)。提示只有與設備存在在線連接時才顯示該頁面。說明手動設置時間 (Time Manually)啟用或禁用手動時間設置。如果啟用該選項，則可編輯“系統時間”(System Time) 輸入框。系統時間 (System Time)按“MM/DD/YYYY HH:MM:

• USS 主站

  功能概述網絡數據傳輸順序這些指令按照輪詢列表（組態 DB）中*的順序循環處理較多 31 個驅動器從站的網絡數據傳輸。 一次只能為每個從站激活一個作業。 用戶將每個從站的網絡數據存儲在一個數據塊（網絡數據塊）中，并從該數據塊中調用數據。 由于已在輪詢列表中的程序定義中*，因此將通過其它數據存儲區（通信處理器 DB）向通信處理器中傳輸數據以及從通信處理器中調用數據。該過程需要兩個函數調用（一個發送