一種帶開關量的開口式電流互感器的應用

    摘 要:介紹了開口式電流互感器在改造項目中的應用,以及帶開關量的開口式電流互感器的作用,和常規開口互感器對比的優勢,并結合工程實例分析。

    Abstract:Introduces the application of open type current transformer in the renovation project, as well as the role of open type current transformer with switching quantity, and the advantages of comparison with conventional open type current transformer, and analyzes with engineering examples.

    關鍵詞 低壓配電系統 開關量 開口式 電流互感器 防竊電 工作原理

    Keywords low voltage distribution system, switching, open type current transformer, anti-theft, working principle

    1.引言 Introduction

    隨著我國電力工業中城網及農網的改造,以及低壓配電系統的自動化程度不斷提高,開口式電流互感器作為低壓配電系統中的一種重要電氣元件,在電網改造中的作用越來越明顯,已被廣泛地應用于測量、計量、繼電保護、系統監測、接地保護和各種電力系統分析之中。

    With the transformation of urban and agricultural networks in China's power industry and the increasing automation of low-voltage distribution systems, open type current transformers, as an important electrical component in low-voltage distribution systems, have become more and more obvious in the transformation of power grids and have been widely used in measurement, metering, relay protection, system monitoring, grounding protection and various power system analysis.

    但是,目前市場上的開口式低壓互感器在安裝的時候可能會出現卡扣沒卡緊導致鐵芯沒有完全閉合;或者在運行過程中,互感器外殼受到很大應力作用,外殼鉸鏈斷裂,導致上下鐵芯不閉合,影響互感器精度或者沒有電流輸出。帶開關量的開口式電流互感器能夠有助于向儀表或者后臺反饋上述情況,在電力監控項目上有廣闊的運用前景。

    However, the open type low-voltage transformers on the market at present may be installed with snaps that are not tightened to cause the core to be not completely closed; or during operation, the transformer shell is subjected to great stress and the shell hinge breaks, resulting in the upper and lower cores not being closed, affecting the accuracy of the transformer or no current output. The open type current transformer with switch can effectively feedback the above situation to the instrument or the background, and has a broad application prospect in power monitoring projects.

    2.電流互感器工作原理 Working principle of current transformer

    開口低壓電流互感器的工作原理如圖1所示,開口電流互感器的一次繞組串聯在被測線路中,I1為線路電流即電流互感器的一次電流,N1為電流互感器的一次匝數,I2電流互感器二次電流,N2為電流互感器的二次匝數,Z2e為二次回路設備及連接導線阻抗。當一次電流從電流互感器P1端流進,P2端出,在二次Z2e接通的情況下,由電磁感應原理,電流互感器二次繞組有電流I2從S1流過,經Z2e至S2,形成閉合回路。由此可得電流在理想狀態下I1×N1=I2×N2,

    所以有I1/I2=N1/N2=K,K為電流互感器的變比。但是由于開

    口式電流互感器的鐵芯切開后,使鐵芯的性能下將的比較厲害,所以要將互感器的鐵芯截面積加大,而且提高安匝數,將I1×N1=I2×N2≥100AN。

    The working principle of the open-ended low-voltage current transformer is shown in Figure 1. The primary winding of the open-ended current transformer is connected in series with the line under test, I1 is the line current, that is, the primary current of the current transformer, and N1 is the primary turns of the current transformer. I2 is the secondary current of the current transformer, N2 is the secondary turns of the current transformer, and Z2e is the impedance of the secondary circuit equipment and connecting wires. When the primary current flows in from the P1 end of the current transformer, and the P2 end goes out, in the case that the secondary Z2e is turned on, according to the principle of electromagnetic induction, the secondary winding of the current transformer has a current I2 flowing from S1, through Z2e to S2, form a closed loop. It can be obtained that the current is I1×N1=I2×N2 in the ideal state, so there is I1/I2=N1/N2=K, and K is the transformation ratio of the current transformer. However, after the iron core of the open current transformer is cut, the performance of the iron core will be worse, so the cross-sectional area of the iron core of the transformer must be increased, and the number of ampere turns must be increased, and I1×N1=I2 ×N2≥100AN.

         

    另外,該互感器上的開關量開關,當互感器卡扣沒卡好或是互感器老化導致殼體破裂,開關按鈕彈起,常閉變常開,信號終止傳輸,互感器無信號輸出;當互感器卡扣正常是,開關狀態為常閉,互感器正常工作。

    In addition, the transformer on the switch, when the transformer snap did not card or the transformer aging caused by the rupture of the shell, the switch button pops up, normally closed to normally open, the ** termination transmission, the transformer no ** output; when the transformer snap is normal, the switch state is normally closed, the transformer works normally.

    3.開口式電流互感器Open type current transformer

    開口式電流互感器主要應用于工業中城網、農網改造項目。特點是安裝方便,*拆除一次母線,亦可帶電操作。但是,目前市場上的低壓開口式互感器存在以下缺點:

    Open type current transformers are mainly used in industrial city network and agricultural network renovation projects. Features are easy to install, no need to remove the primary busbar, and can also be operated with electricity. However, the current low-voltage open type transformers on the market have the following drawbacks.

                    

    (1)市場上的開口式電流互感器在安裝的時候可能會出現卡扣沒卡緊或是鐵芯沒有閉合,在運行過程中會出現互感器脫落或者斷開的風險;

    (1) Open type current transformer on the market may not be installed when the clasp is not tight or the core is not closed, the risk of the transformer falling off or disconnected during operation.

    (2)開口式電流互感器在安裝后如果被人為二次打開后,會出現無信號等問題。

    針對上述不足,AKH-0.66/K-SW系列電流互感器,可以解決上述問題。此互感器外形美觀,安裝維護方便簡潔。如圖2所示,該互感器具備以下幾個優點:

    Open type current transformer will have no ** and other problems if it is artificially opened twice after installation.

    AKH-0.66/K-SW series current transformer can solve the above problems. This transformer has a beautiful appearance and is easy and simple to install and maintain. As shown in Figure 2, the transformer has the following advantages.

    (1)AKH-0.66/K-SW系列電流互感器,安裝時*將電斷開,可以帶電操作,閉合直接使用即可現場安裝簡便,減少人力成本;

    AKH-0.66/K-SW series current transformer, installation without disconnecting the electricity, you can operate with electricity, close the direct use of the site installation is simple, reducing labor costs.

    (2)AKH-0.66/K-SW系列電流互感器,在該模塊有4根引線,兩根傳輸電流信號,兩根傳輸開關量信號;

    AKH-0.66/K-SW series current transformer, there are four leads in the module, two to transmit the current **, two to transmit the switching **.

    (3)AKH-0.66/K-SW系列電流互感器,當卡扣沒卡好或是互感器老化導致殼體破裂,上下殼體彈開,鐵芯接觸不良,卡在互感器下殼體的開關凸起按鈕就會向上彈出,開關斷開,開關量信號終止傳輸,起到提示開口式低壓互感器停止工作的作用。

    AKH-0.66/K-SW series current transformers, when the buckle is not locked or the transformer is aging, the casing is broken, the upper and lower casings pop open, the iron core is in poor contact, and the switch stuck on the lower casing of the transformer protrudes The button will pop up, the switch will be disconnected, and the switching ** will terminate the transmission, which will prompt the open-type low-voltage transformer to stop working.

    (4)AKH-0.66/K-SW系列電流互感器,上下殼體帶有鉛封孔,一旦安裝完畢立即進行鉛封。

    AKH-0.66/K-SW series current transformer, the upper and lower shells with lead seal holes, once the installation is completed immediately lead seal.

    4.參數對照表Parameter comparison table

    4.結束語Conclusion

    AKH-0.66/K-SW系列電流互感器的出現,具備異常打開報警、停上電事件上報等功能,同時也為企業降低了人力物力成本,由于市場巨大,一旦形成生產能力,也可帶動其他行業的飛速發展。

    The emergence of AKH-0.66/K-SW series current transformer, with abnormal open alarm, stop on the power event reporting and other functions, but also for the enterprise to reduce the cost of human and material resources, due to the huge market, once the formation of production capacity, but also can drive the rapid development of other industries.


    江蘇安科瑞微電網研究院有限公司專注于電量傳感器,電流互感器,電能表等

  • 詞條

    詞條說明

  • 能耗監測系統在淼泉衛生院項目的應用

    摘要:隨著社會生活水平的提高,經濟的繁榮發展,人們對能源的需求逐漸增長,由此帶來的能源危機日益嚴重。辦公建筑、醫院、商場等場所如何實時的了解、分析和控制能源消耗已成為需要解決的迫在眉睫的難題。傳統的能源消耗只能以月/季度/年為周期進行,然而辦公建筑、醫院、商場是每日、每時都在進行,能源消耗也是每日、每時的發生。本文介紹淼泉衛生院項目,系統采用現場就地組網的方式,組網后通過Acrel-5000型能耗

  • 功率變送器在造紙磨漿機控制系統中的應用

    摘要:造紙磨漿機控制系統中由PLC通過變頻器控制磨漿機的磨刀進退位移量,功率變送器對磨漿機高壓電機的功率信號進行采集,同時將功率信號以DC4-20mA模擬量信號傳輸至PLC,從而控制系統動態地調節磨漿機的刀距,構成穩定可靠的閉環系統。關鍵詞:功率變送器;磨漿機;PLC;變頻器0.概述 雙盤磨漿機作為國內造紙行業制漿線中使用廣泛的磨漿設備,因各紙種的品質評鑒不同,要求盤磨打漿度不同。磨片之間間隙的大

  • 導軌式直流電能表在充電樁行業中的應用

    摘要:在努力實現“碳中和”的背景下,未來我國新能源汽車的發展趨勢不會改變。目前我國新能源汽車進入黃金發展階段,作為電動汽車的“補給站”,充電樁也呈現出瘋狂式的增長,各地出臺扶持政策,在這樣一個利好的政策下,無疑會提供巨大的市場?;诖耍恼轮饕治隽顺潆姌稇?yīng)用前景以及應導軌式直流電能表的應用。關鍵詞:充電樁;新能源;直流電能表;電動汽車0:概述根據《新能源汽車產業發展規劃(2021—2035年)》

  • 咸陽市朝陽醫院能耗監測系統的研究與應用

    摘要:大型公共建筑總面積不足城鎮建筑總面積的百分之四,但總能耗卻占全國城鎮總耗電量的百分之二十二,大型公共建筑單位面積年耗電量達到70~300KWh,為普通居民住宅的10~20倍。公共建筑是節能大戶和節能主要對象,做好公共建筑節能工作,對推動和帶動全社會節能工作,實現節能減排目標,落實“轉方式、調結構”重大戰略具有重要意義。本文介紹咸陽市朝陽醫院能耗監測系統,采集現場配電室的電力儀表,儀表就地組網

聯系方式 聯系我時,請告知來自八方資源網!

公司名: 江蘇安科瑞微電網研究院有限公司

聯系人: 陳雯

電 話:

手 機: 18761503718

微 信: 18761503718

地 址: 江蘇無錫江陰市東盟路5號

郵 編:

網 址: acrelcw.b2b168.com

八方資源網提醒您:
1、本信息由八方資源網用戶發布,八方資源網不介入任何交易過程,請自行甄別其真實性及合法性;
2、跟進信息之前,請仔細核驗對方資質,所有預付定金或付款至個人賬戶的行為,均存在詐騙風險,請?zhí)岣呔瑁?
    聯系方式

公司名: 江蘇安科瑞微電網研究院有限公司

聯系人: 陳雯

手 機: 18761503718

電 話:

地 址: 江蘇無錫江陰市東盟路5號

郵 編:

網 址: acrelcw.b2b168.com

    相關企業
    商家產品系列
    • 產品推薦
    • 資訊推薦
    關于八方 | 八方幣 | 招商合作 | 網站地圖 | 免費注冊 | 一元廣告 | 友情鏈接 | 聯系我們 | 八方業務| 匯款方式 | 商務洽談室 | 投訴舉報
    粵ICP備10089450號-8 - 經營許可證編號:粵B2-20130562 軟件企業認定:深R-2013-2017 軟件產品登記:深DGY-2013-3594
    著作權登記:2013SR134025
    Copyright ? 2004 - 2025 b2b168.com All Rights Reserved