Configuring Timer DQ operating mode

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：94

Configuring Timer DQ operating mode



Timer DQ

Timer DQ operating mode allows you to output up to two edges per application cycle (for example OB 91, OB 6x) at a specific time, for example, for use as a cam output.

Select the Timer DQ operating mode for the required channel.


圖片: Mode of operation: Timer DQ

Inversion

You can invert the 24 V ** to adjust it to your process. By default, the ** is not inverted.

High-speed output

If you select the high-speed output option, the digital output is switched alternately to 24 V DC and ground.

Advantages of the high-speed output:

Extremely steep edges (output delay in the 1 μs range)

Extremely high switching frequencies

Maximum switching precision, for example, for use as a cam output

Assigning the output cam technology object

The output cam technology object must always be assigned to another technology object whose position is evaluated.

You can assign the output cam technology object to the following technology objects:

Synchronous axis

Positioning axis

External encoder

You can assign exactly one axis or one external encoder to the output cam.

You can assign multiple output cams to one axis or one external encoder.

Configuring the output cam technology object

Select the configuration of the output cam in the Technology objects folder in the project tree.

Configure the basic properties of the technology object in the Basic parameters configuration window.


圖片: Basic parameters

Name

Define the name of the output cam in this field. The technology object is listed under this name in the project tree. The tags of the output cam can be used in the user program under this name.

Assigned axis or external encoder

STEP 7 displays the axis or external encoder assigned to the output cam. You can use the link to directly access the basic parameters of the higher-level technology object.

Output cam type

Select an output cam type on the basis of the required switching behavior:

Position-based cam (position-dependent switch-on/switch-off)

Time-based cam (position-dependent switch-on and position-independent or time-dependent switch-off)

Output cam reference

In this selection, configure whether the switching points of the output cams are to reference the actual position or the position setpoint.

Unit of measurement

The unit of measurement shown for the position of the output cam corresponds to the unit of measurement of the higher-level technology object.

When a time-based cam is selected as the output cam type, the unit of measurement for the switch-on duration and other times is also indicated. The unit of measurement for output cams is always ms.

Hardware interface

Select the type of cam output in the Hardware interface configuration window.


圖片: Hardware interface

Select whether you want to output the switching **s generated at the digital output.

Activate output

Select one of the following two output options for outputting the cam track:

- Output via Timer DQ

For output by Timer DQ, select a cam output in the Output field. The selection box displays all channels that have been configured correctly.

提示 Extending the configuration limits A maximum of eight timer DQ can be configured at the X142 interface. If the Timer DQ at X142 are not sufficient for your needs, you can increase the configuration limits with time-based IO modules: - ET 200SP distributed I/O system: TM Timer DIDQ 10x24V - ET 200MP distributed I/O system: TM Timer DIDQ 16x24V You can find more information on these systems in .




提示 Unsupported instructions for the X142 interface The function blocks for the use of time-based IO (TIO instructions) are not supported by the X142 interface. Recommendation: For the timer DQ, use the output cam or cam track technology object.




- Output by digital output module

For output by a digital output module, select a digital output in the Output field. Only the digital outputs with previously defined PLC tags are displayed for selection.

提示 Output via the X122, X132 or X142 interface Also use the "Output by digital output module" setting in the following cases: - The output occurs at the X142 interface by a DQ instead of a Timer DQ. - The output occurs by a digital output of the X122 or X132 interface (configured ** 39x required) In both cases you must define a PLC tag for the respective I/O address.




Output deactivated
When output is deactivated, the cam track is evaluated only in the software.

Extended parameters > Activation time


圖片: Activation time

The specified output cam type is indicated at the top of the Activation time configuration window.

For a time shift of the switch-on and switch-off times of the output cams, enter an activation time and a deactivation time.

Extended parameters Parameter > Hysteresis


圖片: Hysteresis

To prevent unwanted changes in the switching state of the output cams of a cam track, enter a hysteresis value.

When using output cams that reference the actual position, it is advisable to enter a hysteresis value (> 0.0).

Cam track technology object

In addition to the output cam technology object already described, the cam track technology object is also available.


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• 經典WinCC移植到WinCC Professional

  經典WinCC項目可以有條件的移植到Portal WinCC Professional（專業版）軟件中，但是Portal WinCC Professional項目不可以移植到經典WinCC軟件中。由于經典WinCC的一些功能在WinCC Professional軟件中沒有直接對應的選項，所以將經典WinCC項目移植為WinCC Professional是對舊項目的功能進行刪減的轉換過程。為此，務必

• 傳動裝置 較大頻率

  較大頻率位置反饋在此下拉列表中，能夠以固定級別設置位置反饋信號（編碼器信號 A、B、N）的較大計數頻率。如果您的 CPU 不支持這種功能，則該下拉列表將不可用并顯示為灰色。此處默認設置為“60 kHz”。伴隨信號在此下拉列表中，能夠以固定級別設置長度測量和參考點開關信號的較大計數頻率。如果您的 CPU 不支持這種功能，則該下拉列表將不可用并顯示為灰色。此處默認設置為“10 kHz”。

• PC Access SMART 常見問題

  常問問題1 S7-200PC Access SMART可以與S7-300，S7-400使用嗎？答：不能。2 S7-200PC Access SMART較多可以連接幾個S7-200 SMART PLC？答：8個PLC。3為什么數據條目設置成“寫”，客戶測試端的測試結果為“差”？答：當條目的屬性為“寫”的時候，就取消了該條目的讀取功能，所以客戶端嘗試讀取的時候失敗，質量顯示“差”。在上位機軟件上可以對

• MAC ACL入站規則

  入站規則簡介在此頁面上* ACL 規則，接口將根據此規則過濾入站幀。在“規則組態”(Rules Configuration) 選項卡中* ACL 規則。顯示框說明該頁面包含以下框：接口從下拉列表中選擇所需接口。根據具體設備顯示可用接口。添加規則 (Add Rule)選擇要分配給接口的 ACL 規則。在“規則組態”(Rules Configuration) 頁面中* ACL 規則。添加 (Ad